We've unearthed this great article on Tools You Need to Install a New Bathtub down the page on the net and believe it made good sense to talk about it with you over here.
Installing a tub isn't specifically rocket science, yet it does require strong plumbing, woodworking, and also often, tiling abilities. Replacing an old bathtub with a new one is additionally a reasonably tough job. If the old tub is conveniently obtainable, the task can move speedily; if you need to open a wall surface to eliminate the old tub and place the new bathtub, the task is much harder. In either case, the project is within a house handyman's abilities, although you will require a helper to move out the old tub and also embeded in the new one. Make certain you have actually qualified yourself for the job and also fit attempting it. As opposed to working with a professional to take over a halfway-completed task, it is far better to consider employing one prior to you begin. Opportunities are you may need a specialist plumber to make tube connections.
This article will certainly aid you install a new bathtub in your washroom if you have currently gotten a new tub and also don't need to alter the setup of your previous water supply pipelines.
Your tools as well as material checklist must make up the following:
- New Tub
- Hammer
- Pipeline Wrenches
- Prybar
- Shatterproof glass
- Degree
- Pliers
- Flexible Wrench
- Putty Blade
- Screwdriver
- Cold Knife
- Measuring tape
- Pipeline Caps
Removing Old Taps
If you need to change old taps with new ones as a part of your installation, then the first thing you need to do is disconnect the supply of water. After doing so, switch on the taps to drain pipes any water staying in the system. The procedure of getting rid of the existing faucets can be quite problematic due to the limited accessibility that is typically the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipelines to the taps. Have a fabric ready for the continuing to be water that will come from the pipelines. Once the supply pipelines have actually been eliminated, make use of the same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to stop the single faucets from transforming during this process. As soon as the faucets have actually been removed, the holes in the bath/basin will need to be cleansed of any old sealing compound.
Prior to going on to fit the new taps, contrast the pipeline links on the old faucets to the brand-new faucets. If the old taps are longer than the new taps, then a shank adapter is required for the new taps to fit.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic port to avoid damages to the string. One end of the port fits on the plastic tail of the faucet as well as the other end gives a connection to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly need lowering couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next off, place the faucet in the mounting opening in the bath/basin making sure that the washers are in area between the tap and also the sink. Protect the faucet in position with the producer provided backnut. Once the tap is safely in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with regular tap connectors. The former type ought to be linked to the tap ends initially, tightening just by hand. The supply pipelines can later be linked to the other end. Tighten up both ends with a spanner after both ends have been attached.
Mounting the Bath tub
Making use of both wood boards under its feet, place the tub in the required setting. The wooden boards are handy in uniformly spreading the weight of the tub over the area of the boards as opposed to focusing all the weight onto 4 tiny factors.
The next objective is to guarantee that the tub is leveled all round. This can be achieved by checking the spirit level and also adjusting the feet on the bathtub up until the level checks out level.
To mount taps, fit the bottom of the furthest flexible faucet port to the appropriate supply pipe by making a compression sign up with; then do the exact same for the various other faucet.
Turn on the water and check all joints as well as brand-new pipework for leakages and tighten them if necessary. Fill the bath tub as well as additionally examine the overflow outlet and the typical electrical outlet for leakages.
Lastly, repair the bathroom paneling as defined in the manufacturer's instruction manual. Tiling and securing around the bath tub ought to wait up until the bathtub has been utilized at least when as this will settle it into its last placement.
Planning for the Installment
First of all, the supporting framework supplied with the bathroom ought to be fitted (if called for) according to the manufacturer's guidelines. Next off, fit the taps or mixer to the tub. When suitable the faucet block, it is essential to make certain that if the faucet comes with a plastic washer, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is also sensible to fit a supporting plate under the taps unit to prevent strain on the tub.
Fit the versatile tap connectors to the bottom of the two taps making use of 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet via the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Make certain you make use of every one of the provided washing machines.
Link the catch to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bathroom must now be ready to be suited its final position.
Tiling Around the Bathtub
In the location where the bath meets the floor tile, it is needed to secure the joins with a silicone rubber caulking. This is essential as the installation can move sufficient to break a rigid seal, creating the water to penetrate the wall surface between the bathroom and the tiling, bring about problems with wetness and also possible leaks to the ceiling listed below.
You can choose from a range of coloured sealers to blend in your fixtures and also fittings. They are offered in tubes as well as cartridges, as well as can securing voids up to a width of 3mm (1/8 inch). If you have a bigger void to load, you can load it with twists of soaked newspaper or soft rope. Bear in mind to always fill the bathtub with water before sealing, to allow for the movement experienced when the tub remains in use. The sealer can break fairly very early if you do not take into consideration this activity prior to sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise easily offered on the marketplace. It is suggested to fit the floor tiles using water-resistant or water resistant adhesive and also grout.
How to Install a Freestanding Bathtub?
Installing a freestanding bathtub or any kind of bathtub is not a difficult task if you have a sophisticated guide on installing a freestanding bathtub in your bathroom. Aside from getting the freestanding bathtub to your bathroom, you can do all the work without paying a plumber. A bathroom with a bathtub is a retreat where you can feel the sensation of coming home and soaking in that hot water. It is a great way to remove all the stress from your day.
This guide will walk you through installing a freestanding bathtub in simple steps and help you find relief.
Slope
Make sure your bathroom has a proper slope. If your floor lacks a slope, the water flow to the drain will not function, which leads to a blocked drain which can cost you money. You can use the level device to see your bathroom's vertical and horizontal aspects. Once you have that information, you must carry out the next step.
Placement
A freestanding bathtub has a unique characteristic that helps you bring elegance to your bathroom. A freestanding bathtub comes in various sizes and shapes suitable for different types of bathrooms.
According to the information you gathered from the level device, you must pick a bathtub that suits your style and fits your bathroom aesthetically. You can place a freestanding bathtub virtually anywhere, such as in the corner, near the wall, or even at the center of your bathroom. However, you must ensure proper plumbing where you want to install the tub. If not, then you must call a plumber.
Clean the bathroom floor
After deciding where to place the bathtub, you must clean the entire bathroom floor so that the dust and debris do not accumulate underneath the tub. Simple cleaning is enough, and you will clean it again after the installation.
Steps to Install a Freestanding Bathtub:
STEP 1: Place the protective blanket in the adjacent area where you want to install the bathtub. It will help you protect the bathtub's sides when you do the installation.
STEP 2: Now, place the 4x4 lumber in the area where you want to install the bathtub. Place the bathtub on top of the lumber, and align the drain line with the bathtub drain.
STEP 3: A freestanding bathtub comes with a drain kit. If not, make sure you purchase one with your bathtub. You can pop that drain kit and align it with your bathroom drain line. Ensure that you tighten the drain nut enough so there is no water leakage. You must also clean the bathtub’s drain to remove the factory dirt and debris.
STEP 4: Clean the drain hole in your bathroom. It helps to do the installation without any water blockage. A drain cleaner or bleach will suffice. Once the drain dries entirely, take a small amount of clear silicon and place it around the underside of the pipe flange.
STEP 5: Attach the drain tailpiece to the bottom of the bathtub. Place the rubber or plastic bushing with the plumbing material at the top of the tailpiece and screw the drain nut up the tube until it tightens both the bathtub’s drain and the drain tailpiece. Now you must add the lubricant to the seal to ensure there is no water leakage in the pipe connection.
STEP 6: Place caulk around the bottom edge of the bathtub. Take out the lumbar support and carefully bring the bathtub to the floor. Use a damp cloth to clean the excess caulk and debris and plumber putty to cover the tub drains and the floor.
Tips to Maintain a Freestanding Bathtub:
- Always look for the clog in the drain. You can pull it out with a small stick if hair or debris is in the gutter.
- Use mild cleaning components, which will help you preserve the bathtub for a long time and will also help you remove surface-level scratches.
- Do not use strong solutions such as concentrated bleach to remove stains. Instead, mix water and diluted bleach with a ratio of 10:2, respectively. Apply it to the tub's surface and leave it for 15-20 minutes to remove any surface-level stains.
- Always check the floor drain. You may unclog it using any small sticks or a small vacuum to suck out all the debris.
- Check the heater or faucet immediately if you smell rust or grease in the water. Rust in the water may stain or damage the bathtub in the long run.
- If you want to sand the bathtub, try using 400 grit sandpaper or 600 grit sandpaper for a more refined finish.
As a serious person who reads on Installing A Bathtub, I thought sharing that piece of content was a good idea. If you please take the opportunity to share this page if you liked it. Thanks a lot for going through it.
Immediate attention? Phone us!
Comments on “Plumbing Basics: A Must for Installing a Bathtub”